Shower tray installation

Manual

Shower tray installation manual. This manual has relation on all (color) variants of SaniSupreme® shower trays.

Preparation


Make sure that both a hot water pipe (left) and a cold water pipe (right) are installed at the location where the tap is to be installed, with a center-to-center distance of 135 to 165 mm. IMPORTANT

  • Flush for installation the water pipes Good Through to filthy at to delete.
    This prevents damage to the internals;
  • Check it piping for installation to water hammer to prevent;
  • To damage at prevent is It important that there for It fixed, On- or loosen from An element always An cloth between It tools and It element is becoming placed;
  • SaniSupreme is not responsible for injury that is to arise Through It at tight fixed or tighten by Allen screws, bolts, nuts or similar swivel elements;
  • It is by big interest to after the installation at check or the connections not leaks. To do this, let the water run for a while;
  • SaniSupreme is not responsible for injury to arise Through leaks that could are prevented Through correct installation or Through It check by
  • the crane during the day the installation.


Supplies

- Drill- and screwdriver

- (Laser) spirit level

- Screwdriver

- Spanner

- Teflon tape / sealing tape

- Transparent sanitary sealant

Parts supplied for the installation of a shower tray:

· Shower tray itself

· Mounting material

· (screws, plugs, brackets for mounting)

· Waterproof sealing strip

· (for sealing the edges of the shower tray)

· Wall rosettes and finishing rosettes

· (for finishing the connections of the water pipes at the tap)

 

Important Information:

The shower tray drain kit, including drain, siphon, and built-in drain, is not included as standard with the shower tray. However, these components can be ordered separately from us to ensure a complete installation and efficient drainage. The drain pipe for connecting to the sewer is also not included but can be purchased separately to complete the installation. For more information or to order these components, please feel free to contact us!


 

Shower tray installation

1. Set the shower tray on the wanted place to at check or the position by It drain hole, It drain and the drain pipes match each other

Place the drain plug in the correct position and connect it to the drainpipe. Align the drain plug with the shower tray's drain hole.

Turn the box over and use the cardboard packaging as a protective mat. Place the feet in the indicated position. Tighten the panel clamps on the side where the panels will be connected.

 

2. Ensure the floor is clean, dry, firm, and level. For a rough but relatively flat concrete floor, we recommend that the installer use a purpose-made underlayment to level the area first.

 

3. Remove only the protective film from the drain area and sides of the container. Leave the film on the rest of the container.

 

4. Place the tray in place and level both sides with the adjustable feet. Once the tray is level, adjust all the inner feet to stabilize it. Turn the tray over and apply silicone sealant to the feet and the seam between the shower drain and the shower tray. Place the tray in place and let it cure for 24 hours.

5. First secure the butt panel by pressing it firmly onto the panel clamps, then secure the other panel in the same way.

6. Seal the seam between the shower tray and the tile wall with silicone sealant.

Do not remove any remaining protective film from the shower tray until the shower screen has been fully installed.


Quality, clean and maintenance

This chapter contains everything you need to know about maintaining and cleaning SaniSupreme® products.

 Quality

SaniSupreme® faucets and related products are made of brass or stainless steel. Depending on the chosen SaniSupreme color, various layers are applied to the product, ensuring a strong, wear-resistant, and durable product. Specific properties and instructions for all SaniSupreme colors can be found at www.sanisupreme.nl

Cleaning

Use a mild cleaning agent such as green soap or another mild soap that degreases. Do not use bleach or (harsh) cleaning agents or products based on alcohol or thinners, for example. Never apply the cleaning agent directly to the product; first apply it to a soft cloth or sponge and clean the product with it. Never use a scouring pad, as it can damage the product. After cleaning, rinse the product thoroughly with clean water. This will ensure that no cleaning agent remains.

Thermostat and changeover clean

To clean the thermostat and/or diverter, it must first be removed from the faucet. Follow the steps "Replacing/removing the thermostat internals" to remove the thermostat, and the steps "Replacing/removing the diverter" to replace the thermostat.

/ to delete interior “changeover”. Lay then the thermostat and/or changeover Soak it in a bowl of vinegar for at least 30 minutes. Then rinse thoroughly with clean water and remove any remaining dirt with a cloth. Follow the steps in reverse order to reassemble the faucet.

We councils ten strictest off:

• It usage by aggressive cleaning agents, abrasives, scouring pads or microfiber cloths. This will damage the product;

• It usage by cleaning agents that chlorine, hydrochloric acid, acetic acid or other harmful/ aggressive acids contain. This shall It product damage (and is also also not good for your health);

• It mix by various cleaning agents, the effects by It usage of this untested ones can cause problems;

• It usage by industrial (phosphoric acid) cleaning agents. Also this is not Good for the product (and for your health).

 

Water softener

Water softeners be able to aggressive are ten relative to by metal, protective layers and layers of color by products. This to see We mainly bee water softeners by low quality or water softeners that bad become maintain. Bee An low dH setting takes It risk for damage come on, that's why advise We the water softener not lower in at ask than 4dH. We do not provide a warranty on products affected by a water softener.

 

Warranty- & Terms of Service

On SaniSupreme® products applies under normal circumstances An warranty period 2 years (24 months) after purchase of the product. The conditions under which you can claim the warranty are listed in the SaniSupreme® warranty terms and conditions. You can find the SaniSupreme warranty terms and conditions on the SaniSupreme website.

If you An request to service wishes in at serve bee SaniSupreme® , requests We you first of all Please carefully review the SaniSupreme® Terms of Service. These Terms of Service explain how and where to submit a service request and the service and follow-up process. You can find the SaniSupreme® Terms of Service at www.sanisupreme.nl.

 

}